Front Electronics Network Card PS6PMCM User Manual

Modem Charging Cradle  
User Guide  
This user guide provides an overview of setting up and  
using your new Modem Charging Cradle.  
Model Number: PS6PMCM  
Box Contents  
Please check the Modem Charging Cradle carton for the  
following required items:  
Modem Charging Cradle  
Power Adapter  
Quick install card  
Warranty card  
For more information about these items see More about the  
Box Contents on page 4.  
 
Table of Contents  
Introduction............................................................................................4  
About the Modem Charging Cradle ....................................................4  
Minimum Requirements......................................................................4  
Product Registration...........................................................................4  
More about the Box Contents.............................................................4  
Chapter 1 – Preparing to Use the Modem Charging Cradle ................6  
Installation Overview ..........................................................................6  
Preparing the Modem Charging Cradle for First Use..........................6  
Configuring the Network Manager for Modem Communication...........7  
Chapter 2 – Product/Technical Support ...............................................8  
Product Support .................................................................................8  
Technical Support ..............................................................................8  
Appendix A – Regulatory Information ..................................................9  
Telecom Compliance, Warnings, and Notices ..................................10  
Appendix B – Warranty........................................................................12  
Glossary................................................................................................13  
User’s Guide for Modem Charging Cradle PS6PMCM  
3
 
Introduction  
About the Modem Charging Cradle  
The Modem Charging Cradle enables a telephone connection to a host  
computer. Palm Tungsten E2 handheld users can access and transfer  
critical information as easily as making a phone call. The cradle  
communicates via serial transmission with the Palm handheld. Before it  
can transfer data over the telephone line, the cradle will require third party  
software to be installed on the handheld.  
NOTE  
Palm does not support HotSync over a serial connection, thus  
HotSync is not a supported application for this device.  
Minimum Requirements  
The following minimum requirements must be met for the network,  
handheld and desktop computer to work together:  
Palm Tungsten E2 or compatible handheld  
Power Adapter  
Modem Charging Cradle  
RJ11 phone cable  
A desktop computer connected to a V.34 (or later) modem.  
Product Registration  
Thank you for purchasing this iGo product. We strongly encourage you to  
register this product so that we may keep you notified of pertinent  
updates and relevant product information. Failure to register does not  
diminish your warranty rights. We provide free product support to  
registered users for the first 90 (ninety) days from the purchase date.  
Registration may be completed online at: www.igo.com/registration.  
More about the Box Contents  
Modem Charging Cradle  
The Modem Charging Cradle is designed for and communicates serially  
with the Palm Tungsten E2 or compatible handheld.  
The cradle’s custom-designed mechanical interface connects to the  
handheld in the front, and connects to required services using its three  
rear connections:  
A power receptacle for its power adapter.  
A Line In phone jack that connects the wall (or telephone  
company) line into the device.  
A Line Out phone jack that passes the signal through the device  
to a phone or other device that shares the line.  
User’s Guide for Modem Charging Cradle PS6PMCM  
4
 
NOTE  
Only one device may use the line at a time.  
Front View  
1
Rear View  
#
1
Part Name  
Palm  
multi-Connector Interface  
Line In Phone Jack  
Line Out Phone Jack  
DC Power Receptacle  
2
3
4
2
3
4
Power Adapter  
1
The supplied power adapter is specifically designed for use with the  
Modem Charging Cradle. The power adapter converts standard  
household outlet voltage to the direct current voltage needed to power the  
cradle.  
NOTE  
The Modem Charging Cradle may only be used with  
the following power adapters:  
Phihong Electronics Co., Ltd., Model PSA05R-  
050(PA). (iGo p/n 170140-000)  
User’s Guide for Modem Charging Cradle PS6PMCM  
5
 
Chapter 1 – Preparing to Use the Modem  
Charging Cradle  
Installation Overview  
Before using the Modem Charging Cradle, its hardware and software  
must be properly configured.  
We have provided a step-by-step procedure to help you properly  
configure your new Modem Charging Cradle. The procedure is divided  
into two major tasks.  
Preparing the cradle for first use, and  
Configuring the Network Manager to communicate via the Modem  
Charging Cradle.  
Preparing the Modem Charging Cradle for First Use  
Perform the following steps:  
1. Connect the Modem Charging Cradle to Line Power using the  
supplied power adapters listed on page 5  
2. Connect the Modem Charging Cradle to the Phone Line  
NOTE  
A compliant telephone cable terminated with an  
appropriate and correctly wired local telecom connector  
compatible with the telephone network is required for  
RJ11 connection (using middle line pair) to the modem.  
CAUTION  
Use only No. 26 AWG or larger telecommunication line  
cord to reduce risk of fire.  
Using an RJ11 phone cord, plug one male end into a phone  
wall outlet’s RJ11 receptacle and the other into the cradle’s  
Line-In phone jack.  
WARNING  
The Modem Charging Cradle is designed for  
use on a standard analog phone (or Plain  
Old Telephone Service (POTS)) line. Digital  
lines used in PBX systems are not  
compatible with the Modem Charging  
Cradle and may damage the modem.  
User’s Guide for Modem Charging Cradle PS6PMCM  
6
 
Configuring the Network Manager for Modem  
Communication  
Perform the following steps:  
1. Create a Point-to-Point Protocol (PPP) connection with a remote  
computer by doing these steps:  
On the remote computer, create a connection that will accept  
incoming connections.  
Set the incoming connection device to PC Modem.  
Verify that both, user information and permissions are correct.  
Ensure that the incoming connection has a properly assigned  
IP address.  
2. Configure the Palm Tungsten E2 to work with the Modem  
Charging Cradle:  
Open Preferences from the Palm OS Main Menu.  
Select Communication Connection.  
Create a new connection using these settings:  
Name:  
Connect to: Modem  
Via: Cradle/Cable  
Custom  
Select OK to save the new connection  
Open Preferences from the Palm OS Main Menu  
Select Communication Network then insert these settings:  
Service:  
PSINet  
User Name: <Enter PC User’s Name> who’s being  
connected  
Password:  
Connection: Custom  
Phone: <Enter Phone Number of Remote PC>  
<Enter same PC User’s Password>  
User’s Guide for Modem Charging Cradle PS6PMCM  
7
 
Chapter 2 – Product/Technical Support  
Product Support  
We are committed to providing our customers with first-class customer  
service and technical support. You can receive product support in a  
variety of ways:  
North America Product Support  
Mobility Electronics  
9918 Via Pasar  
San Diego, CA 92126  
Phone:  
Fax:  
E-mail:  
Web:  
(858) 880-2225  
(858) 530-2733  
Technical Support  
For additional information, please refer to the documentation that came  
with the Palm Tungsten E2. If you need additional assistance, you can  
contact technical support via e-mail at: [email protected]  
or directly by phone at (858) 880-2225 and follow the voice prompts to  
our Technical Support personnel.  
Before calling us, please have the following information ready:  
Your name, email address, and phone number  
Your Modem Charging Cradle’s model number  
Your Modem Charging Cradle’s serial number  
NOTE  
The Modem Charging Cradle serial number can be  
found on the product label on the underside of the  
cradle.  
The handheld’s make and model (e.g., Palm Tungsten E2)  
Your computer’s make, model, and operating system  
A detailed problem description  
User’s Guide for Modem Charging Cradle PS6PMCM  
8
 
Appendix A – Regulatory Information  
This device is designed to be compliant with rules and regulations in  
locations it is sold and will be labeled as required.  
CAUTION  
The Mobility Electronics’ Regulatory Engineering  
Department must approve changes or modifications not  
covered in this user guide in writing. Changes or  
modifications made without written approval may void  
the user authority to operate this equipment.  
Radio Frequency Interference Requirement  
FCC Statement  
This equipment has been tested and  
found to comply with the limits for a  
Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are  
designed to provide reasonable  
protection against harmful interference  
in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on,  
the user is encouraged to try to correct the interference by one or more of  
the following measures:  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment and receiver  
Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected  
Consult the dealer or an experienced radio or television technician  
for help.  
Mobility Electronics, Inc. is not responsible for radio/TV interference  
caused by using unauthorized cables or by making unauthorized changes  
to this equipment.  
Radio Frequency Interference Requirement - Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003  
du Canada.  
User’s Guide for Modem Charging Cradle PS6PMCM  
9
 
Telecom Compliance, Warnings, and Notices  
United States  
The applicable regulatory notices for the United States include:  
This equipment complies with Part 68 of the FCC rules and  
requirements adopted by ACTA. On the bottom of this equipment  
is a label that contains a product identifier in the format  
US:AAAEQ##TXXXX. If requested, this number must be provided  
to the telephone company.  
The Ringer Equivalency Number (REN) determines the number of  
devices that may be connected to a telephone line. Excessive  
RENs on a telephone line may result in devices not ringing in  
response to an incoming call. In most areas, the sum of RENs  
should not exceed five (5.0). The REN for this product is part of  
the product identifier that has the format US:AAAEQ##TXXXX.  
The digits represented by ## are the REN without a decimal point.  
This equipment must be connected to the telephone network or  
premises wiring using a compatible modular jack (RJ11C)  
compliant with the applicable FCC Part 68 rules and requirements  
adopted by ACTA. A compliant telephone cord and modular plug  
are provided with this product. It is designed to be connected to a  
compatible modular jack that is also compliant.  
If this equipment, the Modem Charging Cradle PS6PMCM, causes  
harm to the telephone network, the telephone company will notify  
you in advance that temporary discontinuance of service may be  
required. Also, you will be advised of your right to file complaint  
with the FCC if you believe it is necessary.  
The telephone company may make changes in its facilities,  
equipment, operations or procedures that could affect the  
operation of this equipment. If this happens, the telephone  
company will provide advance notice in order for you to make  
necessary modifications to maintain uninterrupted service.  
If trouble is experienced with this equipment, the Modem Charging  
Cradle PS6PMCM, then contact Mobility Electronics (858-880-  
2225) for repair or warranty information. If the equipment is  
causing harm to the telephone network, the telephone company  
may request that you disconnect the equipment until the problem  
is resolved.  
This equipment must not be used on party lines.  
If your home has specially wired alarm equipment connected to  
the telephone line, ensure the installation of this modem does not  
disable your alarm equipment. If you have questions about what  
will disable alarm equipment, consult your telephone company.  
No user repairable parts are contained within this equipment.  
User’s Guide for Modem Charging Cradle PS6PMCM  
10  
 
Canada  
This equipment meets the applicable Industry Canada Terminal  
Equipment Technical Specifications. This is confirmed by the registration  
number on the product label. The abbreviation “IC” before the registration  
number signifies that registration was performed based on a Declaration  
of Conformity indicating that Industry Canada technical specifications  
were met. It does not imply that Industry Canada approved the  
equipment.  
The European Economic Area  
Mobility Electronics, hereby, declares that this device is in compliance  
with the essential requirements and other relevant provisions of Directive  
1999/5/EC. A Declaration of Conformity may be obtained from  
The modem is designed to work with the following Public Switched  
Telephone Networks: Belgium, Netherlands, Luxemburg, Germany,  
France, Italy, Finland, Sweden, Norway, Switzerland, Denmark, UK,  
Ireland, Spain, Austria, Portugal, Greece, Estonia, Latvia, Lithuania,  
Poland, Czech Republic, Slovakia, Hungary, Cyprus, Malta and Slovenia.  
User’s Guide for Modem Charging Cradle PS6PMCM  
11  
 
Appendix B – Warranty  
Mobility Electronics, Inc. warrants this product against defects in materials  
and workmanship to the original purchaser (or the first purchaser in the  
case of the remanufactured product being sold) for a period of one (1)  
year from the date of shipment. This warranty is limited to a repair or  
replacement of the product. To obtain warranty service, the purchaser  
must first call Mobility Electronics, Inc. for an RMA number, then return  
the product to Mobility Electronics, Inc. for repair or replacement.  
Purchaser shall prepay shipping charges for products returned to Mobility  
Electronics, Inc. Mobility Electronics, Inc. will pay for return of the  
products to purchaser, except that purchaser shall pay all shipping  
charges, duties, and taxes for products returned to Mobility Electronics,  
Inc. from a country other than the United States.  
Mobility Electronics, Inc. makes no other warranty of any kind with regard  
to this material. Mobility Electronics, Inc. shall not be liable for errors  
contained herein or for incidental or consequential damages in connection  
with the furnishing, performance, or use of this material.  
Within thirty (30) days of receipt should the product fail for any reason  
other than damage due to customer negligence; purchaser has the right  
to return the product for a full refund of the purchase price. If the  
purchaser wishes to upgrade or convert to another Mobility Electronics,  
Inc. product within the thirty (30) day period, purchaser has the right to  
return the product and apply the full purchase price toward the purchase  
of the other product. Any other return will be subject to Mobility  
Electronics, Inc.’s existing restocking policy.  
MOBILITY ELECTRONICS, INC. WARRANTS THAT THIS PRODUCT IS  
NEW OR HAS BEEN REMANUFACTURED TO MEET NEW  
STANDARDS USING NEW OR SERVICEABLE USED PARTS.  
MOBILITY, INC. MAKES NO OTHER WARRANTY, EITHER  
EXPRESSED OR IMPLIED, WITH RESPECT TO THIS PRODUCT.  
MOBILITY, INC. SPECIFICALLY DISCLAIMS THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE.  
Some states or provinces do not allow limitations on how long an implied  
warranty lasts, so the above limitation or exclusion may not apply to you.  
THE REMEDIES PROVIDED HEREIN ARE CUSTOMER’S SOLE AND  
EXCLUSIVE REMEDIES. IN NO EVENT SHALL MOBILITY, INC. BE  
LIABLE FOR ANY LOST PROFITS, DIRECT, INDIRECT, SPECIAL,  
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED  
ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.  
User’s Guide for Modem Charging Cradle PS6PMCM  
12  
 
Glossary  
ACTA. America's Carriers Telecommunications Association  
Modem. A device for transmitting data over telephone wires by  
modulating the data into an audio signal to send it and demodulating an  
audio signal into data to receive it.  
POTS. An acronym for Plain Old Telephone Service.  
PPP. The Point-to-Point Protocol. This is a communications protocol that  
was defined in RFC 1661, as the Internet standard for transmitting  
network layer IP packets over serial point-to-point links.  
Manual P/N 184324-401-A1  
User’s Guide for Modem Charging Cradle PS6PMCM  
13  
 

Earthquake Sound Speaker CP 8 User Manual
EFJohnson Two Way Radio 001 9800 001 User Manual
Escient MP3 Player MP 100 User Manual
Evo Fitness Treadmill FX40HR User Manual
Extron electronic Switch DVS 510 User Manual
Fisher Price Baby Swing 79667 User Manual
Furuno Marine RADAR FR 604D User Manual
GE Cable Box A016 1CG User Manual
George Foreman Fryer SKG01GFB User Manual
Gitzo Camcorder Accessories G1128 User Manual